Brother Printer Not Turning On: Common Causes and Resolutions

Many of the users face this issue. When they are about to start their day in the office with some important work at hand, their Brother Printer Not Powering On. This leaves them completely stranded looking all around for solutions to get their printing documents tasks back on track. This situation with the Brother printer undoubtedly is quite annoying unless it gets resolved as quickly and it can be.

Guide to Repairing Brother Printer Power Problems Easily

Here we will be providing five detailed procedures to fix the issue of the Brother printer not powering on. So, follow and implement them accordingly as mentioned below and resolve this printer error:

Procedure 1 – Disconnect and Connect the Power Cable to fix Brother printer won’t turn on

The printer’s power cable needs to be disconnected and then reconnected, so do that first. This error message may occasionally display on the device as a result of loose connections. Make sure, then, that the printer and power module are connected correctly. Connect them again if not. To accomplish it, take the following actions:

• Remove the cable from the Brother printer and also the power outlet. 
• Wait for a few seconds
• After that, connect the printer power cable to the power outlet and then press the Power button on the Brother printer to check if the power light indicator starts blinking or not. 

Procedure 2 – Check the Power Cable and Printer’s Power Button to fix Brother printer won’t turn on

If the power cable is broken, the error “Brother printer not turning on” may occasionally appear. As a result, you ought to see if the power line is broken. After removing the power connection from the outlet, look for any obvious damage. In the event that damage is discovered, have it replaced right away.

• Unplug the power cord from the back of the printer and wait for at least 1 hour. Afterward, reconnect the power cord and attempt to turn the printer on.
• It might come as a surprise that when you power down your printer, it doesn’t entirely shut down. Instead, its internal components enter an extremely low-powered state.
• This implies that the issue preventing your printer from turning on can persist even after removing the power source completely!

Disconnecting the power cable for at least 1 hour ensures complete drainage of any residual power from your printer.

Procedure 3 – Clean the Printer to fix Brother printer won’t turn on

If your Brother printer experiences a short circuit, it may indicate a potential ink cartridge leak. It’s advisable to thoroughly clean the printer ink cartridge. After completing this step, check to see if it resolves the issue of the Brother Printer won’t turn on.

Procedure 4 – Check the Cartridge & Print Head to fix Brother printer won’t turn on

Remove the Printhead and inspect the printhead. If the cartridge has dried and you are still printing documents and performing the printer cleaning cycle, the printer might overheat and the print nozzles can catch fire. 

So, take off the print head and disconnect the power for at least one hour. After one an hour, switch on the printer without installing the print head. Once you are done, check if it solves the issue or not.

Procedure 5 – Restore the Power

Once we’ve verified that the printer isn’t in Sleep Mode and ensured the power cable and outlet connections are secure and functional, it’s time to begin restoring power to the printer. There are three slightly varied methods available to attempt the restoration of power to the printer.

Method 1:

1. Unplug the power cord from the outlet and wait for 15 seconds.
2. Press and hold down the Power button. While continuing to hold the Power button, simultaneously plug the power cord back into the outlet.
3. Keep holding the Power button until the printer is completely powered on. If there’s no response after 15 seconds, repeat these steps up to 3 times.

Method 2:

1. Disconnect the power cord from the outlet and wait for 15 seconds.
2. Remove the paper tray.
3. Reconnect the power cord and power on the printer.
4. Once the printer is fully powered on, reinsert the paper tray into the machine.

Method 3:

1. Take out the paper tray.
2. Unplug the power cord from the outlet and wait for 15 seconds.
3. Press and hold down the Power button. While still holding the Power button, plug the power cord back into the outlet.
4. After approximately 10 seconds, the display should show the message “Please put the paper tray firmly back in the machine.”
5. Finally, reinsert the paper tray into the machine.

Procedure 6 – Press and hold the Power button for an extended period

• If your Brother Printer still refuses to power on, attempt a ‘long press’ on the power button.

• While the printer remains plugged in, press and hold the power button for at least 15 seconds

Procedure 7 – Disconnect the USB

If the previously mentioned steps didn’t resolve your printer issue, consider disconnecting the USB connector situated at the rear of your Brother printer. Try powering on the printer again after disconnecting the USB to see if the Brother printer resumes normal operation.

Final Step

These were the 7 procedures in which you can easily resolve the issue of “Brother printer won’t turn on”. Go through these procedures carefully and perform it one-by-one to get rid of this problem on the device.

Author - Komal Hatwaani

I am Komal Hatwaani, aims to provide readers with informative and engaging content that covers everything from technology and business to entertainment and lifestyle. This website dedicated to delivering high-quality content that informs, entertains, and inspires our readers.
Join us on our journey as we continue to explore the ever-evolving landscape of news and information, providing you with valuable insights and perspectives that enrich your digital experience.